The Bitcoin network fee is what you pay miners to put your transaction into a block. It is set by the fee rate you choose, in satoshis per virtual byte (sat/vB), multiplied by the size of your transaction, so it does not depend on how much BTC you send. When many people compete for the next block the rate needed goes up, and when the network is quiet it comes down.
This guide explains where the fee comes from, why two payments of the same amount can cost very different fees, how long a Bitcoin transaction takes, and what to do when one stays unconfirmed. For the steps of making a payment in Sparrow, Electrum or BlueWallet, see how to send bitcoin. Protocol details below come from the Bitcoin developer documentation, the BIPs, Bitcoin Core release notes and Bitcoin Optech, checked on 9 November 2026. No fee figures are given here because they change from one block to the next.
A Bitcoin transaction has no "fee" field. The fee is simply the difference between what the inputs are worth and what the outputs pay out, and the miner who includes the transaction collects it. Your wallet works out that difference for you from the fee rate you pick:
fee (in sats) = fee rate (sat/vB) × transaction size (vB)
So "how much is the BTC fee?" really has two parts: how big your transaction is, which you partly control, and what rate the market needs right now, which you don't.
Your wallet does not hold one balance; it holds separate coins (UTXOs) from each payment you received. To pay someone, it spends one or more of them as inputs and creates outputs: the payment and usually a change output back to you. The Bitcoin developer guide notes that a payment funded by many inputs makes a larger transaction, and a larger transaction costs more at the same fee rate.
| Address starts with | Type | Cost to spend from |
|---|---|---|
1 | Legacy (P2PKH) | Highest: no witness discount |
3 | P2SH, often wrapped SegWit | Lower than legacy when it wraps SegWit |
bc1q | Native SegWit (P2WPKH) | Low |
bc1p | Taproot (P2TR) | Lowest per input; outputs are slightly larger |
Bitcoin Optech's measurements: a one-input, two-output transaction spending native SegWit is 141 vbytes, 35% smaller than the legacy equivalent and 16% smaller than wrapped SegWit. A single-key Taproot input is 57.5 vbytes against 68 for native SegWit, about 15% less, while a Taproot output is 43 vbytes against 31. Taproot therefore pays off most for wallets that spend several inputs at once.
Practical tip: if your wallet has collected many small coins, combining them into one at a quiet time, when low fee rates confirm, means later payments use fewer inputs.
A transaction you broadcast first sits in the mempool, the waiting room of unconfirmed transactions that each node keeps. Miners build the next block from it, and the developer guide describes the order: transactions are added by fee per byte, highest first, until the block is full. Anything paying less waits for a later block.
To see the current situation, open a live mempool view such as mempool.space. Its fee panel shows high, medium and low priority rates, taken from the transactions in the next one, two and three projected blocks. That is the same kind of estimate your wallet makes when it suggests a fee: Bitcoin Optech defines fee estimation as finding the rate that gives a high chance of confirming within a chosen number of blocks.
Bitcoin adds a new block about every 10 minutes on average. The network keeps that pace by adjusting mining difficulty every 2,016 blocks against a target of two weeks. Block discovery is random, though, so the gap between two blocks varies a lot: some follow quickly, others take far longer than 10 minutes.
Wallet presets such as fast, normal and slow are just different block targets. Pick the fast one for anything time-sensitive, such as a swap deposit with a 5-minute rate lock: Superswap.cx waits for 1–3 confirmations on a deposit and most swaps then finish in 5–30 minutes.
If you send funds around regularly, holding part of them as Litecoin or as USDT on Tron means smaller fees and faster confirmations. You pay one Bitcoin fee for the deposit; the payout network fee is already in the quote.
Swap BTC to LTC →An unconfirmed transaction is almost always one whose fee rate is low compared with what else is waiting. It is not lost: the coins have not moved until it confirms. Do not pay the same person again while it is pending, or both payments may end up confirming. There are two ways to speed it up.
The sender broadcasts a new version of the transaction that spends at least one of the same inputs and pays more. Under the BIP125 rules, the replacement must pay both a higher fee rate and a higher total fee. Older nodes only accepted a replacement if the original signalled it could be replaced. Bitcoin Core 28.0 (October 2024) switched the mempoolfullrbf default on, and Bitcoin Core 29.0 (April 2025) removed the option, so nodes on recent Bitcoin Core versions accept replacements without that signal. Your wallet still has to offer a "bump fee" or "speed up" option. The replacement gets a new transaction ID.
Anyone who controls an output of the stuck transaction, the recipient or the sender through the change, can spend it in a new "child" transaction with a high fee rate. A child cannot confirm before its parent, and Bitcoin Core's mining logic looks at the combined fee rate of the two, so miners have a reason to take both. It costs more than RBF because you pay for a second transaction, but it works when you can't replace the original.
Paid a Superswap.cx deposit and bumped the fee? Email service@superswap.cx with your Order ID and the new transaction ID. Wallet-by-wallet steps are in how to send bitcoin.
It changes with every block. Your wallet suggests a rate in sat/vB, and a live mempool view such as mempool.space shows the current high, medium and low priority rates. The fee you pay is that rate times the size of your transaction.
No. The fee depends on the transaction's size in virtual bytes and on demand for block space, not on the amount. A large payment from one coin can cost less than a small payment that spends many small coins.
Blocks come about every 10 minutes on average, so a transaction paying the going rate usually confirms within 10 to 30 minutes. A low fee rate can mean hours or days, and the recipient decides how many confirmations it waits for.
If you sent it, raise the fee with Replace-By-Fee if your wallet offers it. If you are receiving it, spend the incoming output with a high fee using Child Pays For Parent. Otherwise wait for demand to fall, and don't send the payment twice.
Spending from native SegWit (bc1q) or Taproot (bc1p) addresses costs less than spending from legacy addresses that start with 1, because signature data gets a discount in the weight calculation. Taproot inputs are the smallest.
Paid out to your T-address · Rate locked for 5 minutes · From $50 · No account, no ID
Swap BTC to USDT (TRC-20) →Checked 9 November 2026.